Current position > Contact Us
Quick Answer: Digital flow meters with electronic displays give plant teams live rate, total, and alarm data without extra transmitters. Silver Automation Instruments supplies electromagnetic, Coriolis, ultrasonic, vortex, oval gear, and thermal mass flow meters for water, chemicals, fuel oil, gas, and steam. Send your pipe size DN, flow range, pressure bar, and temperature °C for a direct quote.
Factory infrastructure covers many loops. Cooling water, compressed air, steam condensate, fuel oil, and CIP chemicals all need measurement. A digital flow meter replaces manual reading and gives the PLC a clean signal.
A food and beverage plant in Vietnam measures CIP chemical flow every shift. An electromagnetic flow meter with 4-20 mA HART output sends flow rate and total to the PLC. The local electronic display shows kg/h and total liters. Operators see the value from the walkway. No manual dipsticks. No guesswork.
In many sites, an analog gauge only shows a needle. A digital meter adds totalized flow, empty pipe detection, diagnostics, and two way data. Low flow matters when a cooling water imbalance shuts down a compressor. We have seen low flow trips on customer sites many times. The meter catches low flow before a pump runs dry.
An electronic display on a flow meter should be readable at 2 meters. Most engineers skip this part until a meter gets installed behind a pipe rack. Silver Instruments supplies backlit displays with rate, totalizer, and alarm icons. If a loop needs 24/7 trend data, a paperless recorder takes the 4-20 mA signal and stores it.
Here is the thing. A display alone does not make a meter smart. The output matters too. Pulse, 4-20 mA HART, RS485 Modbus, and alarm relays all feed the factory control system. We match the output to your PLC or DCS.
For conductive liquids like wastewater, cooling water, and chemicals, an electromagnetic flow meter works from DN15 up to DN300. Accuracy can reach 0.5% of reading. No moving parts. Liners and electrodes are selected for each fluid.
For diesel and fuel oil, an oval gear flow meter is common. The oval gear meter handles diesel viscosity around 2 to 6 cP with good repeatability. A paint manufacturer in Southeast Asia uses oval gear meters on solvent dosing skids. Last year a customer in Vietnam requested an electromagnetic flow meter for seawater feed to a desalination plant.
For compressed air and flare gas, a thermal mass flow meter or vortex flow meter reports kg/h or Nm3/h. For high viscosity fluids like syrup, polymer, or heavy oil, a Coriolis mass flow meter gives direct mass flow and density. Ultrasonic flow meters work for large water pipes where cutting into the line is costly.
Many factory loops need pressure transmitters near the flow meter. A pressure transmitter with 4-20 mA HART sends upstream pressure. A PT100 temperature sensor provides compensation for thermal mass meters. In ATEX Zone 1 areas, use explosion proof enclosures and intrinsic safety barriers. Tell us the gas group and temperature class before quoting.
Water and wastewater plants often measure conductivity too. Silver Instruments supplies sensors for µS/cm ranges. Flow data plus conductivity gives a fuller picture for reverse osmosis and chemical dosing.
Send us the fluid name, pipe size DN, flow range, pressure bar, temperature °C, and power supply. For conductive water lines, we propose an electromagnetic meter. For diesel, an oval gear meter. For air, a thermal mass or vortex meter. In practice, the more data you share, the faster we can return a technical quote.
If you are not sure about flow range, give us pump capacity or tank volume. We work with those numbers. That approach works for distributors and end users across Southeast Asia, Oceania, Latin America, Africa, and the Middle East.
Send your pressure bar, temperature °C, pipe size DN, and flow range to our team. Call +86-25-68650347 or WhatsApp +86-25-52155837. We reply with a model proposal and price.
Q: What digital flow meter works for a desalination plant seawater intake?
A: An electromagnetic flow meter with PTFE lining and titanium electrodes. Send us flow range in m3/h and pipe size DN. We size the meter for the exact conductivity and pressure.
Q: Can one flow meter display both rate and total flow locally?
A: Yes. Our electronic displays show rate and totalizer. Backlit LCD. 4-20 mA HART and pulse output included. Totalizer units are selectable.
Q: Which flow meter works for diesel generator fuel consumption?
A: An oval gear flow meter. It handles diesel viscosity around 2 to 6 cP. Accuracy still holds. We also supply pulse output for fuel monitoring systems.
Q: Do you supply ATEX Zone 1 rated flow meters?
A: Yes. We supply explosion proof flow meters and pressure transmitters for Zone 1 and Zone 2 gas atmospheres. Provide the gas group and temperature class.
Q: What is the lead time for a digital flow meter?
A: Standard DN15 to DN100 electromagnetic meters often ship in 7 to 15 days. Coriolis and large DN may take 3 to 5 weeks. We confirm at order time.
For a quote, call +86-25-68650347 or WhatsApp +86-25-52155837. You can also reach us on WeChat at +86 15365082610. Send your fluid, pipe size DN, flow range, pressure bar, and temperature °C.
